Toa SR-TB4WP Bedienungsanleitung PDF herunterladen

Turn the bracket base

upside-down to face the

speaker toward the right.

Speaker mounting bracket

(component of the SR-TB4WP)

Screws removed

in Step 3 (M5 x 20)

Waterproof washer

Pad

Note

Take care not to remove the

pad at speaker mounting.

Remove the 8 attached screws.

(The removed screws are used

in Step 4.)

Speaker

[When facing the speaker

toward the left]

Bracket base

(component of the SR-TB4WP)

Hexagon head bolt M8 x 20

(supplied with the SR-TB4WP)

180

ø60

4-12 x 22

[Wall mounting dimensions]

Bolts and nuts used to fix a bracket

base on a wall are not included. Use

bolts and nuts that are appropriate for

the construction of wall.

WARNING

Unit: mm

INSTALLATION MANUAL

WALL TILT BRACKET

SR-TB4WP

The SR-TB4WP is designed to be used exclusively to mount the

SR-S4LWP or SR-S4SWP Line Array Speaker on a wall. It allows

the speaker orientation angle to be adjusted to 0° or 5° vertically

and 20° max. horizontally.

In Combination with the optional SP-131 Speaker Mount Bracket

and YS-60B Pole Band, the SR-TB4WP also permits the speaker

to be mounted on an outdoor pole.

1. SAFETY PRECAUTIONS

• Before installation or use, be sure to carefully read all the

instructions in this section for correct and safe operation.

• Be sure to follow all the precautionary instructions in this section,

which contain important warnings and/or cautions regarding

safety.

• After reading, keep this manual handy for future reference.

3. SPECIFICATIONS

• Accessories

Hexagon head bolt M8 x 20 ............................... 4

• Optional products

Speaker mount bracket: SP-131

Pole band: YS-60B

Note: The design and specifications are subject to change without

notice for improvement.

Step 1. Install the bracket base on a wall.

Determine the orientation of the bracket base

depending on whether the speaker is to face left or

right.

Step 2. Attach the speaker mounting bracket to the bracket

base.

Horizontal facing angle can be adjusted in the range of

0° to 20°.

2. INSTALLATION

Bracket base

Speaker mounting bracket

Horizontal facing angle: 20°

After the speaker's horizontal orientation has been

determined, fix the speaker mounting bracket to the base.

Note

The speaker's horizontal orientation can be adjusted after

the speaker has been installed.

Step 3. Remove the attached screws (with waterproof

washers) on both sides of the speaker.

Step 4. Connect a speaker cable to the speaker.

Step 5. Mount the speaker to the speaker mounting bracket.

The vertical facing angle toward down can be adjusted

either 0° (horizontal) or 5° by the selection of the

screw mounting holes.

Vertical facing

angle: 5°

Vertical facing angle:

0° (horizontal)

• Refer all installation work to the dealer from whom the unit was

purchased. Installation requires extensive technical knowledge

and experience. The speaker may fall off if incorrectly installed,

resulting in possible personal injury.

• Install the unit only in a location that can structurally support the

weight of the unit and the speaker. Doing otherwise may result in

the speaker falling down and causing personal injury and/or

property damage.

• Owing to the speaker's size and weight, be sure that at least two

persons are available to install the speaker. Failure to do so

could result in personal injury.

• Do not use other methods than specified to mount the bracket.

Extreme force is applied to the unit and the speaker could fall off,

possibly resulting in personal injuries.

• Use nuts and bolts that are appropriate for the wall's structure

and composition. Failure to do so may cause the speaker to fall,

resulting in material damage and possible personal injury.

• Tighten each nut and bolt securely. Ensure that the bracket has

no loose joints after installation to prevent accidents that could

result in personal injury.

• Do not mount the unit in locations exposed to constant vibration.

The mounting bracket can be damaged by excessive vibration,

potentially causing the speaker to fall, which could result in

personal injury.

Indicates a potentially hazardous situation which, if mishandled,

could result in death or serious personal injury.

WARNING

Indicates a potentially hazardous situation which, if mishandled, could

result in moderate or minor personal injury, and/or property damage.

CAUTION

• Avoid touching the unit's sharp metal edge to prevent injury.

• Do not stand or sit on, nor hang down from the unit as this may

cause it to fall down or drop, resulting in personal injury and/or

property damage.

• Have the unit checked periodically by the shop from where it was

purchased. Failure to do so may result in corrosion or damage to

the unit that could cause the unit to fall, possibly causing

personal injury.

Number of Speakers 1

to be Mounted

Finish Stainless steel (SUS304)

Dimensions 167 (w) x 247 (h) x 201 (d) mm

(complete assembly)

Weight 2.8 kg (including accessories)

Product Composition Speaker mounting bracket ...... 1,

Bracket base ...... 1

133-01-442-8A

URL: http://www.toa.jp/

2.1. Munting on a Wall

Speaker mounting bracket

(component of the SR-TB4WP)

Bracket base (component

of the SR-TB4WP)

YS-60B Pole Band

(optional)

SP-131 Speaker Mount Bracket

(optional)

Washer*, Nut*

Bolt*

Pole

* Supplied with the SP-131.

[Example of pole mounted application]

The subsequent procedures follow Step2 or later in the

section "2.1. Mounting on a Wall."

The optional SP-131 Speaker Mount Bracket and YS-60B Pole

Band are required to mount the speaker on a pole.

Step 1. Attach the SP-131 to the bracket base using bolts,

washers and nuts supplied with the SP-131.

Determine the orientation of the bracket base in

advance depending on whether the speaker is to face

left or right.

Step 2. Install the SP-131 on a pole using the YS-60B.

The allowable pole diameter is 90 – 340 mm.

For the detailed mounting procedures of the SP-131

and YS-60B, see the instruction manual enclosed with

the SP-131.

2.2. Munting on a Pole

WALL TILT BRACKET 1
SR-TB4WP 1

Inhaltsverzeichnis

Seite 1 - SR-TB4WP

52Turn the bracket base upside-down to face the speaker toward the right. Speaker mounting bracket (component of the SR-TB4WP)Screws removed in Step 3

Kommentare zu diesen Handbüchern

Keine Kommentare

Toa SR-TB4WP Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Akustik Toa SR-TB4WP herunter. Toa SR-TB4WP User Manual [fr] [de] [en] Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Akustik Toa SR-TB4WP