Toa C-CC774 PL Bedienungsanleitung

Thank you for purchasing TOA’s Outdoor Combination Camera. Please carefully follow the instructions inthis manual to ensure long, trouble-free use of

106.1. Precautions When Installing the Camera• Insulate the joint of the camera video output cable and the coaxial cable from other equipment by wrapp

11GNDGNDConnect to the next cameraʼs terminalCamera control cableCamera control cableShield twisted pair cableConnect to remote controllerʼs camera co

7.3.1. Camera Address Setting Switch (DIP Switch 1: No. 1 – 8)Used to set camera address when using the camera in connection with the C-RM500 Remote C

137.3.5. Termination Switch (DIP switch 2: No. 8) Set the switch of the camera last connected to the RS-485 communications line to ON. (Factory settin

14ON123456781173349ON12345678ON12345678ON12345678ON123456782183450ON12345678ON12345678ON12345678ON123456783193551ON12345678ON12345678ON12345678ON12345

15ON1234567865 81 97 113ON12345678ON12345678ON12345678ON1234567866 82 98 114ON12345678ON12345678ON12345678ON1234567867 83 99 115ON12345678ON12345678ON

16ON12345678129 145 161 177ON12345678ON12345678ON12345678ON12345678130 146 162 178ON12345678ON12345678ON12345678ON12345678131 147 163 179ON12345678ON1

17ON12345678193 209 225 241ON12345678ON12345678ON12345678ON12345678194 210 226 242ON12345678ON12345678ON12345678ON12345678195 211 227 243ON12345678ON1

188.1. About Installation• Mount the camera to a heavy-duty wall surface using the optional C-BC711W Wall Mounting Bracket.• When installing the camer

198.3. Wall Mounting Bracket InstallationUse the optional C-BC711W Wall Mounting Bracket.Notes• Check to be sure that wall surface can structurally su

2TABLE OF CONTENTS1. SAFETY PRECAUTIONS ... 32. GENERAL DESCRIPTION ...

208.4. Attaching Housing and Camera Unit to Wall Mounting BracketBefore attaching the housing, waterproof the cable hole with silicone sealant materia

215. Using the 3 supplied camera mounting screws M5 x 12, attach the housing unit to pipe.Tighten 3 screws equally and ensure that no parts rattle.Not

227. Connect the safety wire to the housing projection, then attach the camera unit. Note: Align mark of the camera unit with that of the housing whe

238. Make the camera unit in horizontal position and push it straight up closely to the housing.Cross sectional view of the housingCamera unit12markDu

24Safety wire protrudes from the compartment.Safety wire does not protrude from the compartment.NoteWhen mounting the camera unit to the housing, moun

2510. Tighten 2 camera unit mounting screws to attach the camera unit to the base unit.Camera unit mounting screwCamera unit mounting screw11. Attach

2613. Tighten 4 screws equally to attach the dome cover to the housing and ensure that the dome cover doesnot rattle.12. Align the dome cover’s 4 scre

278.5. Pole Mounting Bracket Installation The optional C-BC771PM Pole Mounting Bracket, C-BC711W Wall Mounting Bracket and YS-60B MountingBand are req

288.6. Suspension Bracket InstallationThe C-BC711P Suspension Bracket is required to suspend the camera from a ceiling.NoteMount the bracket to a conc

29[ RS-485 Communications line control ]Combination cameraMulti-switcherMonitor TVOutdoor combination cameraDedicated Remote controllerNoteCombination

31. SAFETY PRECAUTIONS• Be sure to read the instructions in this section carefully before use.• Make sure to observe the instructions in this manual a

30C-CC714 NT C-CC714 PL24 V AC, 50/ 60 Hz (2P loose end)10 W (normal operation), 80 W max.(2.8 A max)RS-485 communications system (applicable protocol

31C-CC764 NT C-CC764 PL24 V AC, 50/ 60 Hz (2P loose end)10 W (normal operation), 80 W max.(2.8 A max)RS-485 communications system (applicable protocol

32C-CC774 NT24 V AC, 50/ 60 Hz (2P loose end)10 W (normal operation), 80 W max. (2.8 A max)RS-485 communications system (applicable protocol: Type A,

33C-CC774 PL24 V AC, 50/ 60 Hz (2P loose end)10 W (normal operation), 80 W max. (2.8 A max)RS-485 communications system (applicable protocol: Type A,

34• AccessoriesCD-R (CAMERA CONTROLLER Software, installation manual) ... 1Hexagon socket screw M4 x 8 ...

35

133-05-406-0BURL: http://www.toa.jp/

4When Installing the Unit• Avoid installing the unit in locations exposed to sea breeze or corrosive gas. Mounts may become corroded,eventually causin

52. GENERAL DESCRIPTIONTOA’s dome-type color cameras combine with a high-speed camera drive that permits one 360-degreehorizontal rotation per second

64. HANDLING PRECAUTIONS• Noise may appear on the monitor or preset camera positions may deviate with prolonged camera use. Insuch cases, use the came

7• The dome camera features built-in heat generating circuitry. Take care not to touch the internal parts marked“Caution! High Temperature” when worki

8123456[ Housing Appearance ]1314151618191720191012999911117899[ Housing Bottom ][ Camera Unit Top ][ Camera Unit Bottom ]5. NOMENCLATURE[ Appearance

(1) Top cover(2) Safety wire for housing(3) Housing adaptor(4) Safety screw(5) Dome cover(6) Decorative frame(7) Sunshade (Outside)(8) Case (Inside)(9