Toa SR-TP12 Bedienungsanleitung

OPERATING INSTRUCTIONSLINE ARRAY SPEAKERSR-A12L, SR-A12S, SR-A18B,SR-A12LWP, SR-A12SWPRIGGING FRAMESR-RF12, SR-RF12WPTILT JOINT PLATESR-TP12Thank you

106. INTERNAL WIRING DIAGRAMFigures below show the internal wirings of each speaker system.2-1+1-2+LOW -HIGH +HIGH -LOW +2-1+1-2+HIGH +HIGH -Speaker c

118. DIGITAL PROCESSOR SETTINGSRecommended setting parameters are as follows.System using the SR-A12L, SR-A12S, SR-A12LWP or SR-A12SWPSystem which com

129. FLYING9.1. General DescriptionUse the SR-RF12(WP) Rigging Frame for flying the Line Array speaker. With the use of the SR-RF12(WP), upto 8 Line A

1343 degrees5 degrees5 degrees5 degrees5 degreesSR-A12LSR-A12L SR-A12L SR-A12LSR-A12S15 degrees15 degreesSR-A12SEnclosure opening angle: 4 degreesEncl

149.3. Joining the Enclosure to the Rigging FrameFlying Plates are mounted at both the front and rear of the enclosure’s sides. Follow the procedure b

159.4. Joining EnclosuresUse the supplied Joint Plate to join the enclosures by way of the enclosure's flying plate. As shown in thefigure, mount

169.5. Notes on Flying•Check to confirm that the suspension wires, belts, construction of theceiling, etc are strong enough to withstand the speaker l

17• Only the SR-A12SWP or SR-A12LWP Line Array speaker can be installed outdoors. There is no Subwooferavailable to be installed outdoors.• WP type sp

1810. STACKING10.1. General DescriptionLine Array speakers can be stacked using the SR-RF12 Rigging Frame. Up to 5.5 speakers can be stacked,counting

1910.3. Mounting the Enclosure to the Rigging Frame Flying Plates are mounted to the front and rear of the enclosure’s sides. Follow the procedures be

2TABLE OF CONTENTS1. SAFETY PRECAUTIONS ... 32. GENERAL DESCRIPTION ...

2010.4. Joining EnclosuresFor joining enclosures, refer to “9 Flying, 9-4. Joining Enclosures”. 10.5. Notes on Stacking• Prepare casters and caster mo

2110.6. Tilting the Enclosure DownwardThe lower Line Array speaker, excluding the subwoofer, can be tilted downward with the addition of SR-TP12Tilt J

22Typical stacking example using the tilt joint plateSR-A18B x1, SR-A12S x1, SR-A12L x3Vertical facing angle: 0 degree - 15 degrees(Left side) (Right

23SR-A12L SR-A12SBass-reflex typeContinuous program, Low frequency: 450 W, High frequency: 180 WLow frequency: 8 Ω, High frequency: 16 ΩLow frequency

SR-A18BBass-reflex typeContinuous program: 720 W8 Ω95 dB (1 W, 1 m)40 – 400 Hz (when using the optional DP-0206)80 Hz (when using the optional DP-0206

• Avoid installing or mounting the unit in unstablelocations, such as on a rickety table or a slantedsurface. Doing so may result in the unit fallingd

4• When unpacking or moving the unit, be sure tohandle it with two or more persons. Falling ordropping the unit may cause personal injury and/orproper

52. GENERAL DESCRIPTIONTOA’s SR-A series Line Array speaker employ unique wave front control technology to create a sound fieldwith high sound clarity

6Input panel(Rear)(Front)740467716282433399(Right side)(Left Side)Joint plate (accessory)Flying plate (Front)Flying plate (Rear)15˚Input panel(Rear)(F

7Input panelAir Hole (Bottom only)Green LOW (+)Black LOW (-)Red HIGH (+)White HIGH (-)Joint plate (accessory)Flying plate (Front)Flying plate (Rear)(R

8Caster Mounting Plate16-M1021-ø20595164140716728664.5719518010535155050800719569536(Top)(Front)(Right side)(Left side)(Bottom)SR-RF12, SR-RF12WP4846(

95. INPUT CONNECTORSSR-A12L, SR-A12S and SR-A18B (for Indoor use)Figures below show the input connector arrangements of each speaker system. Since con